ARC Billet Rod, GX200 & 196cc Clone Stroker 3.707
Item No: 6268
Brand: ARC
IN-STOCK
SHOP ALL PARTS BY CATALOG
New ARC Billet Rod for the Honda and Clone Motors.
Billet Rod ARC Pro Series featuring the industries only forced oil dipper for superior oiling to the crank pin. CNC machined from 7075 T-651 aluminum and are designed to withstand the rigors of today's high horsepower kart engines. These rods boast advanced oiling design and high strength ARP rod bolts. These are simply the best rods money can buy. Rod includes bearing and bolts.
This rod was designed to work with our #11132P series Wiseco piston which will require machining(remove approximately .090 from top of piston) and #6521 HD wrist pin. Call us to help you choose the best rod for your application.
Rod bolt torque: 170 in/lbs lubricated
Installation Instructions:
To install your ARC rod you will need a 12 point 1/4" socket and a QUALITY inch pound torque wrench. You will need an outside micrometer, dial bore gauge or plasti gauge, and oil.
Measure the crank pin diameter with the outside mic, it should measure 1.180" +/-.0005". Measure in several spots to insure roundness. If out of round more than .0005" it probably should be replaced. The crank pin finish should be smooth to the touch.
When disassembling the rod notice on the side of the rod with the part number there are two dots next to the separation point of the beam and cap. These dots help to re-orientate the cap and beam when assembled. The side of the rod with the part number engraved will always face the side cover side.
Make sure the bearing and rod serrations are clean and install the bearings. Lubricate the rod bolt threads and hand tighten the bolts. Using the torque wrench tighten the bolts to 60" lbs. Alternate each side to increase the torque by 20" lbs at a time until you reach 150"lbs. Then loosen the bolts and repeat the torque process. this helps seat the rod bearing especially on a new rod. Measure the bore with your dial bore gauge opposite the parting lines. If using plasti gauge you will have to install the rod on the crank and use in accordance the plasti gauge instructions.
The rod bore should measure 1.183 +/.0005". With plasti gauge you are looking for about .003" clearance. From .0025-.0035" clearance is acceptable. Anything outside that dimension please call 800-521-3560 for recommendation.
Once clearance is set apply oil to rod, crank, and wrist pin and install this time torque to 170"lbs.
Improperly torquing rod bolts is one of the most common causes of rod failure.
New ARC Billet Rod for the Billet Rod 3.625 in. GX 200 or 196cc Clone Stroker.
It is one of our Pro Series Rods, featuring ARC's trademark forced oil dipper.
PARTS INFORMATION over 21,000 parts
- IDENTIFY YOUR MODEL
This can be one of the biggest challenges in ordering correct parts. If you ordered
your Vehicle from us, we can look-up your records.
- FACTORY PARTS
150/300 TrailMaster, Kandi,
IceBear, Kinroad, Hammerhead,
Roketa
- MINIBIKE PARTS
Manco, Kenbar, Yerf-Dog, Kartco, Carter, Azusa, Taco, Bonanza, Little BadAss, American Racer
- DIRT BIKE PARTS
70, 110, 125, 150, 250cc SSR, Apollo, PitsterPro, Thumpstar, Roketa
- GOKART PARTS
Manco, Kenbar, Kartco, Yerf-Dog, Carter, Azusa, TopKart
- ATV PARTS
110, 125, 150cc, Coolster, Icebear, Trailmaster, Kandi, Kayo
- SCOOTER PARTS
50, 150cc Icebear, BMS, SSR, Znen, Trailmaster
- PERFORMANCE PARTS
150/250/300cc TrailMaster, Kandi, Icebear,
Kinroad, BMS, Roketa, SunL, American Sportworks,
Carter, Dazon
ALL PARTS
see all categories
choose Free Gifts or get an Extra Discount
Product Reviews
Engines
New ARC Billet Rod for the Billet Rod 3.625 in. GX 200 or 196cc Clone Stroker.
It is one of our Pro Series Rods, featuring ARC's trademark forced oil dipper.
new
2-lbs
//gokartsusa.com/images/products/detail/6270.jpg
Red/Black/Blue
6268
ARC
|
|