12V 6AH Battery YTX7A-BS, Batteries PS104-15

12V 6AH Battery YTX7A-BS
Item No: PS104-15
Brand: ZPS
EASTER SALE: $51.11
IN-STOCK
factory parts, see return policy
12 Volt 6 Amp YTX7A-BS Battery - Maintenance Free Dry AGM w/Acid Pack. Fits full-size scooters, mopeds, ATVs, dirt bikes, motorcycles, off-road vehicles and much more.

**Note: This product is a ORM-D (Other Regulated Item, Domestic) regulated item and ships via FedEx Ground to the lower 48 states only.
  • Length: 5.90 inches (150mm)
  • Width: 3.40 inches (86mm)
  • Height: 3.70 inches (94mm)
  • Includes Acid Pack
  • CCA (cold cranking amps): 90


Set-Up Instructions

All AGM battery electrolyte containers are not the same. Each contains the proper amount of electrolyte for its specific battery. Before filling, read the electrolyte handling instructions and precautions on the label. Do not smoke when activating a battery or handling battery acid. Always wear plastic gloves and protective eye wear and be sure to read the Battery Safety section in this manual. The following seven steps should be used to activate an AGM battery:

1. The battery must be out of the vehicle and placed on a level surface.

2. Remove electrolyte container from the plastic storage bag. Remove the strip of caps. Put the strip aside as you will use it later to seal the battery cells. For battery filling use only the dedicated acid container that comes with the battery as it contains the proper amount of electrolyte for that specific battery. This is important to service life and battery performance. Do not pierce, or otherwise open the foil seals on the electrolyte container. Do not attempt to separate the individual electrolyte containers.

3. Place the electrolyte container with the foil seals facing down into the cell filler ports on the battery. Hold the container level and push down to break the foil seals. Electrolyte will start to flow into the battery and air bubbles will be seen inside the container. Do not tilt the electrolyte container.

4. Check the electrolyte flow. Keep the container in place until it empties completely. If no air bubbles are coming up from the filler ports, or if container cells havent emptied completely after 20 minutes, tap the container and/or battery case a few times to cause the electrolyte to flow into the battery. Do not remove the acid container from the battery until it is completely empty. The battery requires all of the electrolyte from the container for proper operation. Bubbles will appear as the electrolyte container fills the battery indicating the flow of battery acid. Tap the container periodically to keep the electrolyte flowing until the container is completely empty. Never puncture the top of the acid container to speed up the filling process.

5. Remove the empty electrolyte container from the battery. Fully insert the strip of sealing caps (previously removed from the electrolyte container) into the battery filling ports. Make sure the strip of caps is fully inserted and flush with the top of the battery. Insert the caps by hand, do not use a hammer or excessive force. Never remove the strip of caps or add water or electrolyte to the battery during its service life.

6. For batteries with ratings of less than 18 AH, let the battery stand for 20 to 60 minutes. For batteries with higher AH ratings allow the battery to stand for 1 to 2 hours. AGM batteries have the amp hour (AH) printed on the front of the battery case. The stand, or rest period, allows the electrolyte to permeate into the plates for optimum performance.

7. Newly activated AGM batteries require an initial charge. After adding electrolyte, a new battery is approximately 75-80% charged. After the stand period (step 6), charge the battery to bring it to a full state-of charge. The battery charger used for initial charging should be able to charge at 12.8+-volts for an AGM battery.

12V 6AH Battery YTX7A-BS


PARTS INFORMATION
over 11,000 parts
  • IDENTIFY YOUR MODEL
    This can be one of the biggest challenges in ordering correct parts. If you ordered your Vehicle from us, we can look-up your records.
  • FACTORY PARTS
    150/300 TrailMaster, Kandi, IceBear, Kinroad, Hammerhead, Roketa
  • MINIBIKE PARTS
    Manco, Kenbar, Yerf-Dog, Kartco, Carter, Azusa, Taco, Bonanza, Little BadAss, American Racer
  • DIRT BIKE PARTS
    70, 110, 125, 150, 250cc SSR, Apollo, PitsterPro, Thumpstar, Roketa
  • GOKART PARTS
    Manco, Kenbar, Kartco, Yerf-Dog, Carter, Azusa, TopKart
  • ATV PARTS
    110, 125, 150cc, Coolster, Icebear, Trailmaster, Kandi, Kayo
  • SCOOTER PARTS
    50, 150cc Icebear, BMS, SSR, Znen, Trailmaster
  • PERFORMANCE PARTS
    150/250/300cc TrailMaster, Kandi, Icebear, Kinroad, BMS, Roketa, SunL, American Sportworks, Carter, Dazon


ALL PARTS   see all categories
  GOKART/MINIBIKE PARTS   FACTORY PARTS   PERFORMANCE
  PARTS   TRAILMASTER   BUGGY PARTS
  ENGINES   TRAILMASTER 150 ENGINE   150 BUGGY
  TORQUE CONVERTER   KINROAD   150 ENGINE
  GOKART SPEED   TRAILMASTER 300   150 TRANSMISSION
  MINIBIKE SPEED   HAMMERHEAD   250 BUGGY
  TIRES   BUGGY TIRES   ALL TIRES
  WHEELS   BUGGY WHEELS   ALL WHEELS
  ATV PARTS   DIRT BIKE PARTS   SCOOTER PARTS
  ATV PARTS   PIT BIKE 70/110/125/250   SCOOTER PARTS
  ATV TIRES   HONDA CRF50/70   50 SCOOTER
  ATV WHEELS   PIT BIKE ENGINES   150 SCOOTER
  CHINESE BIKE PARTS   HONDA CLONE PARTS   MINI CHOPPER PARTS
  POCKET BIKE -33,36,49cc   TITAN TX200   LITTLE BADASS
  GY6 50/125/150   PREDATOR 212   150 SCOOTER
  DIRT BIKE 50/70/110/125   HONDA GX200   150 SCOOTER
choose Free Gifts or get an Extra DiscountSELECT A FREE GIFT
  FREE HELMET   FREE GOGGLES   FREE GLOVES

Product Reviews

Rate This Product:
or Create a Review
(0 Ratings, 0 Reviews)


BUGGY 150 Performance 12V 6AH Battery YTX7A-BS new 8-lbs https://www.partsforscooters.com/core/media/media.nl?id=454048&c=ACCT120207&h=abc47f2b84a2f22879be Red/Black/Blue PS104-15 ZPS